Diagnostic Trouble Code
P07BA
Transmission Park Position Sensor/Switch B Circuit High
Technical Description P07BA
Transmission Park Position Sensor/Switch B Circuit High
Severity Level P07BA
The severity of this code varies based on the specific malfunction and the severity level may progress if not corrected in a timely manner. This code could become a safety issue requiring immediate attention if the starter will engage with the vehicle in gear.
What Does This Mean P07BA?
This is a generic powertrain diagnostic trouble code (DTC) and applies to OBD-II vehicles that have a transmission park position switch/sensor. That may include but is not limited to vehicles from Dodge, Ford, Toyota, Land Rover, VW, Chevrolet, etc. Although generic, the exact repair steps may vary depending on year, make, model and powertrain configuration.
Trouble code P07BA is one of several possible codes associated to the Transmission Park Position Sensor/Switch "B" Circuit.
This code is an indication that the Powertrain Control Module (PCM) has detected a malfunction that is affecting the operation of the transmission park position sensor/switch "B" circuit. The codes that are commonly associated to transmission park position sensor/switch "B" circuit malfunctions are P07B8, P07B9, P07BA, P07BB, P07BC and P07BD. The specific situation determines the code activated by the PCM and the check engine light or the service engine soon light will be illuminated.
The purpose of the transmission park position sensor/switch "B" circuit is to monitor the status of the transmission. This circuit sends a signal to the PCM when the transmission is placed into the park position. Based on the specific vehicle, this circuit is commonly a safety feature to prevent the starter from engaging with the automatic transmission in gear.
Code P07BA is set by the PCM when the transmission park position sensor/switch "B" circuit is detected as having high output voltage.
Trouble code P07BA is one of several possible codes associated to the Transmission Park Position Sensor/Switch "B" Circuit.
This code is an indication that the Powertrain Control Module (PCM) has detected a malfunction that is affecting the operation of the transmission park position sensor/switch "B" circuit. The codes that are commonly associated to transmission park position sensor/switch "B" circuit malfunctions are P07B8, P07B9, P07BA, P07BB, P07BC and P07BD. The specific situation determines the code activated by the PCM and the check engine light or the service engine soon light will be illuminated.
The purpose of the transmission park position sensor/switch "B" circuit is to monitor the status of the transmission. This circuit sends a signal to the PCM when the transmission is placed into the park position. Based on the specific vehicle, this circuit is commonly a safety feature to prevent the starter from engaging with the automatic transmission in gear.
Code P07BA is set by the PCM when the transmission park position sensor/switch "B" circuit is detected as having high output voltage.
Symptoms P07BA
1
Vehicle will not start (starter will not engage)
2
Starter will engage with the vehicle in gear
3
An illuminated Service Engine Soon Light
4
Check Engine Light is illuminated
5
Transmission may not shift out of park
6
Transmission may not shift into park
Possible Causes P07BA
1
Defective transmission park position sensor/switch
2
Corroded or damaged connector
3
Damaged or faulty wiring
4
Defective PCM
Solutions & Repair Steps P07BA
The first step in the troubleshooting process for any malfunction is to research the Technical Service Bulletins for known issues with the specific vehicle.
Locate all of the components associated with the transmission park position sensor/switch "B" circuit. This will include the transmission park position sensor/switch, wiring, connectors and the PCM on a simplex system. Based on the specific year, make and model of the vehicle this circuit may incorporate more components. After these components are located, a thorough visual inspection should be conducted to check all of the associated wiring and connectors for obvious defects such as scraping, rubbing, bare wires or burn spots. The connectors should also be checked for corrosion build up or damaged pins.
The advanced steps become very vehicle specific and require the appropriate advanced equipment to perform accurately. These procedures require a digital multi meter and the specific technical references for the vehicle. Voltage requirements will vary based of the specific year, make and model of the vehicle.
Voltage requirements will vary based on the specific vehicle, the transmission park position sensor/switch circuit configuration and the components incorporated. Technical data should be referenced to obtain the correct voltage range for the transmission park position sensor/switch and the appropriate troubleshooting sequence to follow. The correct voltage input to a sensor/switch with no voltage output is normally an indication of internal failure.
If this process identifies the absence of a power source or ground, continuity testing may be needed to check the condition of the wiring and connectors. Continuity tests are always performed with the power removed from the circuit and the normal readings should be 0 ohms of resistance unless otherwise specified by the technical data. Resistance or no continuity is an indication of faulty wiring or connectors that are shorted or open and must be repaired or replaced.
Hopefully, the information in this article has been helpful to point you in the right direction to correct the problem with your the transmission park position sensor/switch circuit. This article is strictly informational and the specific technical data and service bulletins for your vehicle should always take priority.
Locate all of the components associated with the transmission park position sensor/switch "B" circuit. This will include the transmission park position sensor/switch, wiring, connectors and the PCM on a simplex system. Based on the specific year, make and model of the vehicle this circuit may incorporate more components. After these components are located, a thorough visual inspection should be conducted to check all of the associated wiring and connectors for obvious defects such as scraping, rubbing, bare wires or burn spots. The connectors should also be checked for corrosion build up or damaged pins.
The advanced steps become very vehicle specific and require the appropriate advanced equipment to perform accurately. These procedures require a digital multi meter and the specific technical references for the vehicle. Voltage requirements will vary based of the specific year, make and model of the vehicle.
Voltage requirements will vary based on the specific vehicle, the transmission park position sensor/switch circuit configuration and the components incorporated. Technical data should be referenced to obtain the correct voltage range for the transmission park position sensor/switch and the appropriate troubleshooting sequence to follow. The correct voltage input to a sensor/switch with no voltage output is normally an indication of internal failure.
If this process identifies the absence of a power source or ground, continuity testing may be needed to check the condition of the wiring and connectors. Continuity tests are always performed with the power removed from the circuit and the normal readings should be 0 ohms of resistance unless otherwise specified by the technical data. Resistance or no continuity is an indication of faulty wiring or connectors that are shorted or open and must be repaired or replaced.
Hopefully, the information in this article has been helpful to point you in the right direction to correct the problem with your the transmission park position sensor/switch circuit. This article is strictly informational and the specific technical data and service bulletins for your vehicle should always take priority.
Related Codes
P07B8
Transmission Park Position Sensor/Switch B Circuit Open
P07B9
Transmission Park Position Sensor/Switch B Circuit Low
P07BB
Transmission Park Position Sensor/Switch B Circuit Performance Low
P07BC
Transmission Park Position Sensor/Switch B Circuit Performance High
P07BD
Transmission Park Position Sensor/Switch B Circuit Intermittent/Erratic