Diagnostic Trouble Code
P0313
Misfire Detected with Low Fuel
Technical Description P0313
Misfire Detected with Low Fuel
What Does This Mean P0313?
This is a generic powertrain code, which means it covers all makes/models, 1996-newer. However, specific troubleshooting steps will vary depending on the vehicle.
Code P0313 refers to an engine misfire under low fuel conditions. It is one of a few ambiguous codes on a vehicle, which if taken at face value, diagnosed and corrected seems straightforward enough.
The code is set when the computer --through signals from a range of sensors -- determines that the engine miss is due to a lean (to much air and not enough fuel) condition. If the fuel level is low enough to uncover the fuel pump, sporadic pressure surges due to the pump's inability to pick up the remaining fuel will cause a "Lean" condition.
In all likelihood you have either lowered the fuel level to low before refilling, or you have a legitimate fuel delivery problem. If the fuel system proves to be working properly, several other mechanical failures can cause this scenario.
Code P0313 refers to an engine misfire under low fuel conditions. It is one of a few ambiguous codes on a vehicle, which if taken at face value, diagnosed and corrected seems straightforward enough.
The code is set when the computer --through signals from a range of sensors -- determines that the engine miss is due to a lean (to much air and not enough fuel) condition. If the fuel level is low enough to uncover the fuel pump, sporadic pressure surges due to the pump's inability to pick up the remaining fuel will cause a "Lean" condition.
In all likelihood you have either lowered the fuel level to low before refilling, or you have a legitimate fuel delivery problem. If the fuel system proves to be working properly, several other mechanical failures can cause this scenario.
Symptoms P0313
1
Trouble code P0313 misfire detected with low fuel
2
Rough running engine
3
Hard or no start
4
Hesitation on acceleration
5
Lack of power
Possible Causes P0313
1
Low fuel level exposing fuel pump
2
Failing fuel pump
3
Fuel filter clogged
4
Fuel pressure regulator failure
5
Clogged or failed fuel injectors
6
Short or open circuit in fuel pump harness
7
Poor electrical connectors
Solutions & Repair Steps P0313
It's important to start by going online and checking all the relevant TSBs (technical service bulletins) relating to this code. If the fuel system is not the problem, several vehicles have a peculiar problem that tends to set this code.
For example, BMWs have a set of three oil separator hoses beneath the intake manifold that when cracked, create a vacuum leak that sets this code.
Check your factory and extended warranty to see if it is still covered, and for how long.
Purchase a code scanner from your local auto parts store, or borrow one. They are relatively inexpensive and not only retrieve the codes, but they have an accompanying code cross-reference sheet for explanations and can reset the computer upon completion.
Connect the scanner to the OBD port below the dash on the driver's side. Turn the key to "On" and depress the "Read" button. Make a note of all the codes and cross-reference them with the code sheet. Additional codes could be present that will direct you to a particular area, such as:
Repair any additional code(s) and retest by clearing the code with the scanner and test driving the vehicle.
If no supporting codes are present, then start with the fuel filter. The following diagnosis and repair procedures require a few special tools:
Make sure there is at least a half a tank of fuel.
If the fuel pump is faulty, take it to a service facility to replace. It makes technicians nervous when dropping the fuel tank. One spark can bring disaster. Don't attempt it at home, lest you blow up your house and the surrounding homes if an unfortunate accident should occur.
For example, BMWs have a set of three oil separator hoses beneath the intake manifold that when cracked, create a vacuum leak that sets this code.
Check your factory and extended warranty to see if it is still covered, and for how long.
Purchase a code scanner from your local auto parts store, or borrow one. They are relatively inexpensive and not only retrieve the codes, but they have an accompanying code cross-reference sheet for explanations and can reset the computer upon completion.
Connect the scanner to the OBD port below the dash on the driver's side. Turn the key to "On" and depress the "Read" button. Make a note of all the codes and cross-reference them with the code sheet. Additional codes could be present that will direct you to a particular area, such as:
Repair any additional code(s) and retest by clearing the code with the scanner and test driving the vehicle.
If no supporting codes are present, then start with the fuel filter. The following diagnosis and repair procedures require a few special tools:
Make sure there is at least a half a tank of fuel.
If the fuel pump is faulty, take it to a service facility to replace. It makes technicians nervous when dropping the fuel tank. One spark can bring disaster. Don't attempt it at home, lest you blow up your house and the surrounding homes if an unfortunate accident should occur.